Corner cases of Ubuntu 14.04 on Lenovo ThinkPad x201

I've been using Ubuntu 14.04 for a couple months now.

1. CPU got stucked on 1.2GhZ

Recently I installed a handy utility called indicator-cpufreq, which gives a system status bar icon indicating the currently used CPU governor and the current cpu frequency.  I noticed that my CPU always got stucked on 1.2Ghz, no matter what I did. I have tried modifying it manually by echo-ing the sysfs node and using cpufreq-utils, without much luck. I then came across this page:

http://askubuntu.com/questions/340626/permanently-change-maximum-cpu-frequency

This page explains that there is a CPU bios_limit that if set wrongly, may prevent the CPU from going above the frequency threshold that's set there.

cat /sys/devices/system/cpu/cpu0/cpufreq/bios_limit

Turned out it really was the culprit!! For some weird reason it got set to 1.2GHZ!!

This is how you worked around it:

echo 1 > /sys/module/processor/parameters/ignore_ppc

To make workaround permanent, we can edit the kernel command line argument, just like what's explained on the same page:

Modify /etc/default/grub to be like this:

GRUB_CMDLINE_LINUX_DEFAULT="quiet splash processor.ignore_ppc=1"

Everything works like a charm afterwards!

I then installed cpufreqd, which is a daemon to customize CPU frequency based on the laptop's realtime battery status (e.g. power level, plug/unplugged, etc). Now my docked x201 is running buttery smooth at 2.67 GHZ :)

I want to check out how long will it take to build AOSP on this laptop now :)

2. Intermittent shutdown due to overheating

Another problem I was facing is that after a couple hours of running docked, my laptop would shut itself off! When this happened, I undocked my laptop and noticed that it's abnormally hot!

I then realized that x201's airflow is located on its bottom, which got blocked by the dock. (sigh.. guess the dock isn't poorly designed.... :( )

Don't fret out though! There's solution!
I found this handy tool to control the fan speed of the laptop's.

http://www.thinkwiki.org/wiki/How_to_control_fan_speed

Basically, x201's fan can be controlled by this node:

/proc/acpi/ibm/fan

There are several levels that can be set, which corresponds to the RPM of the fan.

With this in mind, thinkfan can be used to automate the RPM of the fan depending on the reading of the thermal sensors. This page kindly describes how to set it up. (including how to run thinkfan as a daemon, custom setup for x201, etc)

http://staff.science.uva.nl/~kholshei/thinkfan_guide/

Edit (10/06/2015):
The following steps are how I did it:
1. sudo apt-get install thinkfan
2. sudo echo "options thinkpad_acpi fan_control=1" > /etc/modprobe.d/thinkpad_acpi.conf
3. sudo vim /etc/default/thinkfan, change it to be the following (this is to load thinkfan on boot):
START=yes
4. sudo vim /etc/thinkfan.conf, change it to be the following (this is fan vs. sensor-reading):

# The way the config works is that it picks the highest value among all sysfs nodessensor /sys/devices/virtual/hwmon/hwmon0/temp1_input
sensor /sys/devices/platform/coretemp.0/hwmon/hwmon2/temp4_input
sensor /sys/devices/platform/coretemp.0/hwmon/hwmon2/temp2_input
#sensor /proc/acpi/ibm/thermal

(0, 0, 47)
(1, 46, 50)
(2, 49, 53)
(3, 52, 56)
(4, 55, 59)
(5, 58, 62)
(6, 61, 65)
(7, 64, 75)
#127 is for disengaged
(127, 74, 32767)

And for debugging:
1. To see how a new config file works:
sudo thinkfan -n
2. To check current temperature:
cat /sys/devices/virtual/hwmon/hwmon0/temp1_input && cat /sys/devices/platform/coretemp.0/hwmon/hwmon2/temp4_input && cat /sys/devices/platform/coretemp.0/hwmon/hwmon2/temp2_input
'or'
cat /proc/acpi/ibm/thermal (in ubuntu 14.04, only shows one temperature)
3. To check fan level:
cat /proc/acpi/ibm/fan
(level shouldn't be 'auto' if thinkfan is really running)
4. ps aux | grep thinkfan <- you should see the process running